#Microsoft xbox 360 wireless receiver driver windows 8 software download

First, if you donвЂ™t have it already, download theВ Xbox 360 Accessories Software for your operating system from the Microsoft gaming software download site, and install it.

#Microsoft xbox 360 wireless receiver driver windows 8 drivers

inf file that comes with the official Microsoft drivers to allow for the different PID of the RF controller of the Xbox 360. Once you have that all soldered up, you have yourself a wireless dongle for your Xbox 360 wireless controller, something like this: I was paranoid enough about it to actually test the unit on my old Macbook (that I neither care about nor use) before trusting it on my main machines. From what IвЂ™ve read in comments in various places the RF board likes to burn out quite spectacularly without a diode in place, taking the USB controller itвЂ™s connected to with it. The diodes that you put in series on the power line will lower the voltage to tolerable levels for the board вЂ“ almost exactly 3.3V, to be honest (my multimeter is showing 3.34V). The whole board runs on 3.3V while USB standard is 5V. I will mention again that the diodes are ABSOLUTELY NECESSARY. IвЂ™m not going to make a project box for it or anything, and itвЂ™ll be hidden away somewhere so practicality > looks. I could have been neater, but I honestly didnвЂ™t see much point. I chose to cut the diode legs down a fair bit and soldered it off to the left of pin 1, along the bottom edge of the RF module. Basically, follow the picture (click for bigger image):Д«eginnerвЂ™s mistake/brain fart moment warning: Make sure the diode is the right way around.

Instead IвЂ™ll assume youвЂ™re sitting there with an RF board, a USB cable ready for soldering, a diode, and a hot soldering iron.

#Microsoft xbox 360 wireless receiver driver windows 8 how to

And thatвЂ™s your part.ДЄs youвЂ™re reading this and have an interest in it IвЂ™ll assume you know how to cut, strip, and tin your wires, so IвЂ™ll not bother with that part. DonвЂ™t go trying to pry it off like I almost did. ItвЂ™s held on by 3 screws, so be sure to pop the little plastic part off to find the third screw. ItвЂ™s the board on the front of the machine where the ring and power button are. Pro tip: Instead of a small plastic knife that they say to use to ping open the case, you can either buy a tool for it, make one out of an old CD/DVD spindle cover, or just rip the damn thing open with a screwdriver (after all, itвЂ™s dead right?). has a perfectly good explanation of how to do this. IвЂ™m not going to reinvent the wheel here. Basically itвЂ™s just there for a forward voltage drop WHICH IS VITAL (unless you donвЂ™t mind burning the board out and killing your USB controller).

Two diodes вЂ“ a couple of 1N4001 or equivalents will do.

Any old USB cable you donвЂ™t mind cutting.

Dead/Red Ringed Xbox 360 you donвЂ™t mind cannibalising.

Well, I say modification but I really mean little more than soldering a few wires and altering a. The wireless transceiver in the Xbox can be made to work with a little modification. This is the key to getting the controller working with a PC. Now if youвЂ™re like me, and have a spare wireless controller sitting around, itвЂ™s likely you have a dead red ringed Xbox 360 sitting in a cupboard. I was thinking that there may be some other RF transceiver that could be modified or adapted to work with it. As IвЂ™m tight on cash right now I figured IвЂ™d have a quick look around to see if there was a way to use a wireless controller on the PC without going out and buying the official wirelessВ transceiver. Yesterday I had a thought вЂ“ I donвЂ™t like having a wire to the Xbox360 controller I use for games on my PC.

#Microsoft xbox 360 wireless receiver driver windows 8 update

Update 5: Further testing on alternative syncing method shows how non-play & charge kit compatible peripherals can be synced -without- a microcontroller. Update 4: Alternative means of syncing mentioned in the comments by George. You can find the related forum post here: Link (and see how my thrown together version of it looks and.

#Microsoft xbox 360 wireless receiver driver windows 8 serial

However, I am working with another modification I found which adds LED and sync enable functions by means of a serial connection with a PIC16F628A ОјC. Update 2: It seems that syncing is impossible directly from the RF module and PC, but if the wireless controller you use was already synced with the RF module, and hasnвЂ™t been re-synced with another Xbox since, it will work. I also added actual photos of the wiring now, as IвЂ™ve redone it (hence the messy wires from re-solderingВ Etc.) Two diodes in series take the voltage down to almost exactly 3.3V, which is the required voltage for the RF board. Update: I updated the post to mention using two 1N4001 or equivalent diodes instead of just one. Please note that I barely pay attention to this site anymore and is only here for archive purposes.